Bestone vape oem center believe that many people have such a problem: I have not favored my pole or box for a while, why does it become “core”? The color of the oil in the oil storage compartment changed, and even the oil in the oil bottle also changed color. expired? The temperature is too high? Or poisoned?

Bestone vape oem center also see such a problem, the liquid in the oil storage tank turned dark red, what happened to it that I don’t know? Let’s unravel these questions together today.

1.Discoloration of e-liquidoil in the oil tank

This kind of situation is often seen in oil storage atomizers. Most of these situations occur because the heating wire is soaked in the e-liquid for a long time, which causes the iron element in the heating wire to precipitate and enter the oil storage tank along the cotton conduction, so the e-liquid is turned red or dark red.

The fuel consumption of the mouth suction oil storage atomizer is relatively small. The rod or box holding the small smoke, or the players who have just been exposed to electronic cigarettes, the speed of e-liquid consumption is relatively slow, and the frequency of smoking e-cigarettes is low. The e-liquid is stored in the If the oil tank cannot be pumped out in time, this will happen over time.

The solution is to add the amount of e-liquid as needed, not to add too much at one time, and ensure that you can drain the added e-liquid within a day.

2.A brown layer deposited on the surface of the e-liquid

This usually happens in winter. In fact, substance is not damaged by the e-liquid, but because the nicotine solution and colored essence are float on the surface of the e-liquid. The reason for this is because of cold weather or high VG content.

When the weather gets colder, the fluidity will become lower, the tolerance to nicotine or dark flavors will become worse, and there will be saturation and precipitation. Also, if the VG content is too high, VG does not have a good bearing capacity for the flavor, and the nicotine will be slowly repelled by the VG first, and finally float on the surface.

The solution is very simple. Warm the e-liquid bottle with your palm, then shake the bottle and repeat it several times to remix the nicotine, essence and solution evenly.

3.The color in the e-liquid bottle changes

Most of this happens because the e-liquid is exposed to the air, exposed to direct sunlight, or placed for too long, so that the nicotine or essence is oxidized and discolored. It is normal for this to happen, and the flavor of the e-juice will generally not change, and it can be used normally, so there is no need to worry about it.

The solution is tighten the e-liquid and place it in a ventilated and dark place. It is best to smoke it within three months after opening.

4.E-liquid burn the core

There are two reasons for this situation, one is the essence with high sugar content in the e-liquid, and the other is the high VG content of the e-liquid. There is no solution to the former, which belongs to the positioning of the e-liquid itself.

The latter is because VG itself is relatively viscous, and pure VG conducts oil very slowly in cotton. If the oil storage atomizer uses e-liquid with a high VG content (such as e-liquid with 80% VG content), then the continuous vaping Sometimes the supply of e-liquid is prone to be insufficient, and at this time there will be a burnt wick.

If it is used on a dripping oil atomizer, after opening the cap and refueling, you just start to smoke when you see the oil on the surface of the cotton wick, and there will be burnt wicks Case. (Vape Master e-liquid: PG30%/ VG70%)

The solution is that if you are using a finished atomizer, then try not to use those e-liquids with high sugar content. If you using a DIY atomizer, then improve your own cotton, use cotton with a faster oil conduction speed, or drip the e-liquid and wait for 15 minutes, wait until the e-liquid is completely immersed in the atomizing core.

About Bestone vape oem factory:

Shenzhen Bestone Technology Co., Ltd. is a global leader in offering vaping OEM/ODM solutions with cutting-edge R&D technology, massive manufacturing capacity, wide range of product’s portfolio and diverse client base.All our products are ISO9001:2000, RoHS, CE, FDA, PSE, UL, and SGS certified.With a decade of OEM/ODM experience for top vaping brands, BESTONE has developed unique heating technology as well as structure, material and design solution to revolutionize the e-cig industry.